What areas around Bristol do you cover?
We cover a fairly wide area around Bristol including Bath, Clevedon, Portishead, Thornbury, The Chew Valley and Yate. We have taken commissions to install as far away as London, Liverpool and Oxford so please get in touch if in doubt. We never say never.
What aspects of the job do you undertake?
We are happy to complete as much or as little as you need, from building work through to stove supply and installation.
I have a fireplace with an old gas fire. Can it be easily removed so that a wood burner can be installed?
Yes! We often remove period fireplaces and replace with a fantastic woodburner installation. If you have a gas fire you will need to get a Gas Safe registered heating engineer to disconnect the gas supply first if it is still live. We will carry out all aspects of restoration and rebuilding ready for the stove to be installed, such as acid-washing brick work, re-pointing, rendering or boarding. The choice depends on you preferred finish.
I think my fireplace is too narrow to fit a wood burner. What are my options?
A stove should have reasonable clearance to each side. Most manufacturers recommend around 150mm as a guide but we will assess each situation individually. We will help you determine which stove models could fit. Fireplaces can usually be widened if needed.
Can I keep my wooden surround if I have the rest of the fireplace removed?
It depends upon the stove installed. A stove will have recommended clearances to combustible materials and we can help you determine if your surround can be kept. If needed, a heat shield can be used to protect a surround.
What are my options regarding the hearth?
You need a reasonably sized hearth to sit the wood burner on. There needs to be at least 225mm of clearance from the front of the stove to the edge of the hearth. The hearth needs to be higher than the surrounding floor or clearly marked by a perimeter such as a rail. Hearths can be made of many materials such as slate, stone, granite or tempered glass. We process slate hearths in-house and can provide samples on request.
Do I need a multi-fuel stove?
That depends on whether you ever intend to burn smokeless solid fuel (e.g anthracite or coke) or just wood. All stoves can burn wood but multi-fuel stoves can also burn appropriate solid fuel such as coke. Several stoves can be fitted with a multi-fuel ‘kit’ so initially the woodburning only model can be purchased and then upgraded at a later date. A woodburning only model usually burns wood more effectively than a similar multi-fuel model.
What size wood burner should I get?
There is a rule-of-thumb guide which takes into account only the volume of the room. In metres, length x height x width / 12 = approximate kW of wood burner for that room. But there are many other factors which should influence the decision. This is why you should use a registered installer to help you assess your requirements and guide you to the right model of stove.
I’ve just had my stove installed and it’s giving off a burning smell when I use it. Is it dangerous?
Your installer should have advised you that the first few times a stove is heated, the new paint on it can give off fumes as it cures. Usually this lasts no more than 2-3 firings. If it persists then contact your installer and ask them to investigate.
What size flue does a wood burning stove use?
If the stove is not DEFRA approved then it must use at least a 150mm or 6″ flue. A DEFRA approved stove can use a 125mm or 5″ flue. If you are only going to use smokeless fuel and your stove has a 5″ flue then the flue in the chimney can be 5″.
Should I get a convector or radiant stove?
A convector stove typically has special side panels that allow air to circulate more efficiently around the room. This works especially well in larger rooms with more air to heat. Due to the gap between the panels and the stove body, the sides of the stove are slightly cooler than a radiant stove. A radiant stove emits heat from all sides although some radiant stoves have heat shields to the rear and underneath to allow them to be placed closer to walls and on floor plates.
Will installing a stove cut down on draughts?
Yes! When the stove is installed, the original chimney/flue will be closed off using a register plate. When the stove is not in use and the door is closed, to all intents and purposes this major source of draughts in a room will be stopped. When the stove is in use, it will be drawing a much lesser amount of air than an open fire would.
I don’t have a chimney, can I get a wood burner?
Yes you can. By using a twin-wall flue system, a wood burner can be safely installed into a building with no existing chimney or masonry flue. This is especially useful for houses where the downstairs chimney breast has been removed but the upper chimney system is still intact. If the intended stove location has no chimney system at all then the twin-wall flue can either go up through the ceilings and floors then out through the roof or it can go out through an external wall and up the side of the building. We can supply flues in several powder-coated colours so it doesn’t have to be plain steel.
My chimney is leaking smoke into the house, what can I do?
If you have a woodburning stove then we can line your chimney with a solid fuel grade liner. If you have an open fire then we can line your chimney with a solid fuel liner which would normally need to be at least 8″ in diameter. We would test your chimney prior to re-lining to check that there are no other leaks. We can carry out all aspects of building work to recondition your fireplace as this can also be a source of leaks.